Download Article

Download Commodity

A water heater can be an eyesore if information technology stands out from the residue of your room, but there are a few ways that yous can hide it stylishly. If yous want a simple solution, a room divider can hands block your view of the water heater. Curtains hung from your ceiling can also give you a light, cheap alternative. Edifice a cabinet around your water heater not only conceals it, but gives you an additional shelf of storage infinite. No thing how you hide your water heater, your room will instantly wait great!

  1. one

    Measure out the height of your h2o heater. Kickoff your measuring tape at the lesser of your water heater and extend information technology to the full peak of the water heater. Include the height of any pipes that extend upward and out from the superlative of the water heater if y'all besides desire to conceal them. Write downwards your measurement as presently equally you take it then you don't forget.[one]

    • Yous may also mensurate the width and depth of the water heater, but these measurements are non as important every bit the acme since you can adjust how long a room divider is.

  2. 2

    Buy a room divider that completely hides your water heater. Visit a abode goods store or store online for multi-panel room dividers that will fit in your space. Wait for i that is tall enough to conceal the water heater and is able to wrap around the sides. Try to observe a divider that matches the design in the rest of the room then it doesn't stand out or seem out of identify in your room.[two]

    • If you can't find a room divider that can completely cover the water heater, you lot may need to buy multiple.
    • Room dividers can be made from many different materials and with unlike designs. Choose one that fits best in your space.

    Advertisement

  3. 3

    Environs your water heater with the room divider. Stand up the room divider up and pull the panels apart so information technology doesn't fall over. Button the divider about 6 inches (15 cm) in front of the h2o heater so one edge is against the wall. Pull the other cease of the divider to extend and wrap information technology around the h2o heater until you tin't see it anymore. Whenever you need to access the h2o heater, button the divider against the wall.[three]

    Warning: Don't rest the divider against a gas water heater since it could be a fire gamble.

    4. Advertisement

  1. 1

    Measure the width and depth of the water heater. Extend a record measure out from one wall until you've reached the outer edge of the heater. Write down your measurement and add nigh four–5 inches (10–13 cm) to information technology so the curtain has some infinite between it and the water heater. Take the depth measurement from the second wall behind the heater to the furthest point it extends out. Add another 4–five inches (10–xiii cm) to the measurement to add a buffer.[4]

    • Don't install your drape so it straight touches the water heater since information technology could create a burn down run a risk.

  2. ii

    Find the height of your ceiling. Offset your tape measure on the floor well-nigh your water heater and pull it straight upwards until you accomplish the ceiling. Ensure that the tape is perfectly vertical or else your measurement will exist wrong. Write down your measurement and so yous don't forget information technology and so you know how long your curtain needs to be.[5]

  3. 3

    Buy ceiling drape track that's the same length as the width and depth combined. Pall rail is a metal piece that y'all tin can hang a drapery from the ceiling with. Get a length of rail to install directly on your ceiling that matches the combined length and width measurements you took. If you want your curtain to wrap around the h2o heater completely, so get angled corner sections of track every bit well.[6]

    • You can buy curtain tracks from home good stores or online.
    • If you lot can't find the exact length that yous need, employ a hacksaw to cut the track to size.

  4. iv

    Screw a piece of curtain track on the ceiling. Position the stop of the showtime runway section against the wall so it extends out past your water heater. Make sure the runway isn't crooked on the ceiling before feeding screws into the holes along it. Use an electrical screwdriver to secure the screws and so the rail stays in place.[7]

    Tip: If you're putting your screws into drywall, employ anchors earlier you put them in or else the rail could fall out of identify.

  5. five

    Slide the drape hooks onto the start piece of rail. Make sure to employ curtain glider hooks that match the width of your track. Push the round end of the claw into the track and slide them to the end. Add as many hooks as yous demand for your curtain correct away since it's more difficult to put hooks on once you finish the rest of the runway.[8]

    • You can buy curtain glider hooks from home goods stores or online.
    • Hooks come in multiple sizes and styles. Go hooks that lucifer the hardware in the residue of your room so they don't stand out too much.

  6. half dozen

    Install the rest of the drape rail. Position the tracks on the ceiling so they wrap around your water heater completely. Agree the track pieces upward against the ceiling and feed screws into the holes along their lengths. Brand sure the ends of the rail line up with the slice y'all already installed before using your electric screwdriver to secure them in identify.[nine]

    • You may need to utilize an angled slice of rail if y'all need your mantle to wrap around in a corner.

  7. seven

    Hang a floor-length drape from the hooks. Go a curtain that's the same height as your ceiling so you tin hibernate the entirety of your water heater. Guide the hooks through the holes along the top edge of the mantle and spread it out around the track. Once you've placed all the hooks, slide the curtain along the track to conceal your water heater.[10]

    • Get a pall that matches the other styles in your room so it doesn't stand out or disharmonism.
    • Information technology'due south okay if your mantle is a piddling bit taller than yous need it to exist since you can use hem record to shorten it.

    8. Advertisement

  1. 1

    Measure the height, width, and depth of the h2o heater. Position your tape measure on the flooring underneath your h2o heater and extend the tape up to the superlative border. And then measure how far your water heater extends out from each wall that's adjacent to it. Add about 2–three inches (v.1–vii.half-dozen cm) to each measurement and then you have extra space around the heater. Write downwardly your measurements and then you don't forget them later on on.

  2. two

    Cut 1 in × iv in (2.5 cm × 10.2 cm) boards to your measurements. Get enough ane in × four in (ii.v cm × 10.2 cm) lumber to cut out 5 pieces that equal your tiptop measurement, iii pieces equal to your width, and 2 pieces that are the same as the depth. Put your boards on a sturdy work surface then the slice you're cutting hangs over the border. Agree the wood in place with your nondominant hand and cut through the pieces with a handsaw.

    • For example, if the dimensions of the cabinet are fifty by 18 past 18 inches (127 × 46 × 46 cm), and so you need 5 pieces that are 50 inches (130 cm) long, three pieces that are 18 inches (46 cm), and ii pieces that are 18 inches (46 cm).
    • This cabinet is meant to use with a water heater that'south in the corner. If your water heater isn't in the corner, then you need vi pieces equal to the height, 4 pieces equal to the width, and two pieces equal to the depth.

  3. iii

    Assemble the boards into 2 rectangular frames for your cabinet. Lay out two boards for the elevation of your cabinet and position 2 boards for the width perpendicularly betwixt them. Make sure the length of the top board is flush with the terminate of the lath on the side. Position the second board so it's 3–4 inches (seven.6–10.2 cm) from the bottom of the side pieces. Screw the pieces together to course a rectangular frame that has 2 legs extending out from the lesser. Repeat the procedure for the other frame piece.

    • Always exit room betwixt the bottom of the board and the floor since gas h2o heaters could cause a buildup of harmful gas if it's sealed.
    • These frames fit around a water heater in the corner of a room. If your water heater isn't in the corner, and then make three frames instead.

  4. four

    Cover the large middle section with plywood. After you have the frame assembled, measure the inside window on each console and add 1 inch (ii.5 cm) to each side. Cutting pieces of 1⁄4 inch (0.64 cm) plywood to size using a handsaw or a tabular array saw. Put the console on one side of the frame and staple around the outer edge of the plywood. Put staples in every 2 inches (5.ane cm) along the border so it stays in place.

    • You can also utilize cloth if you want your cabinet to wait more decorative.

  5. 5

    Screw the frames together in the corner to make an L-shape. Stand the frames up on their legs and position them so they class a right angle. Clench the forest pieces together so they don't move around and spiral them together. Place a screw every iv–5 inches (10–thirteen cm) so the chiffonier doesn't fall autonomously.

    • For a water heater that isn't in the corner, add the tertiary frame to your cabinet to brand a U-shape.

    Tip: Utilize pocket holes if you don't desire the screws visible when you're finished.

  6. half-dozen

    Adhere a rear support leg onto your chiffonier. Clamp the last short slice to the meridian corner of the cabinet and spiral on an bending bracket to concord information technology in place. Employ the last long piece of wood you cut and screw it onto the end of the short piece so it'due south held in identify. The extra leg will add additional support then you can put more weight on top of the cabinet when it's finished.

    • You do non have to add together an boosted leg if you don't want, but don't shop any heavy items on top of the cabinet.
    • Don't add an additional support leg if you fabricated a cabinet that has 3 sides.

  7. 7

    Nail plywood or wood planks on top of the cabinet. Measure out the dimensions of the peak of your cabinet and so you can cut out the top slice. Y'all can either use multiple ane in × iv in (two.v cm × 10.2 cm) planks or a single sheet of plywood. Cut the pieces to size and drive nails every 4 inches (10 cm) along the edge of the chiffonier to concord the top piece in place.

    • Make certain the top of your chiffonier doesn't crash-land into whatever pipes or else it may not fit well in the space.

  8. 8

    Slide the cabinet over your water heater to conceal information technology. Put the open end of the cabinet so it faces the water heater and brand sure the 2 paneled sides face up out. Slowly push your chiffonier over the water heater. Use the planks or plywood you put on top of the cabinet as a shelf to store items in the room.

    • For example, if your water heater chiffonier is in the laundry room, you may continue detergents and laundry supplies on top.

    9. Advertisement

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advert

Cheers for submitting a tip for review!

  • Don't completely seal off a gas water heater since it could cause a buildup of harmful gas.

  • Avoid resting a room divider or curtain confronting a h2o heater to prevent whatsoever fire hazards.

Advertisement

Things Y'all'll Need

  • Measuring record
  • Room divider
  • Measuring record
  • Ceiling curtain track
  • Electrical screwdriver
  • Curtain hooks
  • Floor-length curtain
  • ane in × 4 in (2.5 cm × x.2 cm) boards
  • Plywood
  • Hand saw
  • Measuring tape
  • Forest screws
  • Electrical screwdriver
  • Wood staples
  • Stapler
  • Nails
  • Hammer

References

About This Article

Thank you to all authors for creating a page that has been read 60,635 times.

Did this article help you?